From: "Danjel Jungersen" <none@danjel--jungersen.dk.lh.bsd-dk.dk> To: bsd-dk@bsd-dk.dk Date: Sat, 03 Sep 2005 15:45:27 +0200 Subject: pkg_add og php
Hej allesammen...
Jeg har forsøgt at installere php på min OpenBSD 3.6 uden held.
Når jeg prøver:
pkg_add -v php4-core-4.4.0.tgz
fik jeg først dependencies fejl, dem har jeg lagt i samme mappe, så
den ser jeg ikke mere.
Men nu kommer "Segmentation fault".
Hvad gør jeg galt, og er der en nemmere måde at få gang i php?
TIA
Danjel
dmesg:
OpenBSD 3.6 (GENERIC) #59: Fri Sep 17 12:32:57 MDT 2004
deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: AMD-K6tm w/ multimedia extensions ("AuthenticAMD" 586-class) 200 MHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,MCE,CX8,MMX
real mem = 66691072 (65128K)
avail mem = 53334016 (52084K)
using 839 buffers containing 3436544 bytes (3356K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(a8) BIOS, date 03/19/97, BIOS32 rev. 0 @ 0xfb400
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xb8c4
pcibios0: PCI BIOS has 6 Interrupt Routing table entries
pcibios0: PCI Interrupt Router at 000:07:0 ("Intel 82371AB PIIX4 ISA" rev 0x00)
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc0000/0x8000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel 82439TX System" rev 0x01
pcib0 at pci0 dev 7 function 0 "Intel 82371AB PIIX4 ISA" rev 0x01
pciide0 at pci0 dev 7 function 1 "Intel 82371AB IDE" rev 0x01: DMA, channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <Maxtor 6E040L0>
wd0: 16-sector PIO, LBA, 39205MB, 80293248 sectors
atapiscsi0 at pciide0 channel 0 drive 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <ASUS, CD-S400/A, 1.2C> SCSI0 5/cdrom removable
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
cd0(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 disabled (no drives)
uhci0 at pci0 dev 7 function 2 "Intel 82371AB USB" rev 0x01: irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
"Intel 82371AB Power Mgmt" rev 0x01 at pci0 dev 7 function 3 not configured
rl0 at pci0 dev 15 function 0 "Accton MPX 5030/5038" rev 0x10: irq 10 address 00:10:b5:3a:87:a6
rlphy0 at rl0 phy 0: RTL internal phy
vga1 at pci0 dev 16 function 0 "Matrox MGA Millenium 2064W (Storm)" rev 0x01
wsdisplay0 at vga1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask fb65 netmask ff65 ttymask ffe7
pctr: user-level cycle counter enabled
dkcsum: wd0 matched BIOS disk 80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
fd0a: hard error writing fsbn 19 (st0 44<abnrml,top_head> st1 2<write_protect> st2 0 cyl 0 head 1 sec 2)
fd0a: hard error writing fsbn 19 (st0 44<abnrml,top_head> st1 2<write_protect> st2 0 cyl 0 head 1 sec 2)
fd0a: hard error writing fsbn 7 of 7-9 (st0 40<abnrml> st1 2<write_protect> st2 0 cyl 0 head 0 sec 8)
fd0a: hard error writing fsbn 16 of 16-18 (st0 40<abnrml> st1 2<write_protect> st2 0 cyl 0 head 0 sec 17)
This archive was generated by hypermail 2b30 : Wed 15 Nov 2006 - 18:24:52 CET