From: Jakob Kjøller <none@jakob--kjollers.dk.lh.bsd-dk.dk> To: <none@bsd-dk--bsd-dk.dk.lh.bsd-dk.dk> Subject: SV: Accesspoit på en OpenBSD Date: Sat, 3 Sep 2005 01:25:48 +0200
Jeg er ved at gå helt balsitisk, jeg har fulgt div vejledninger, bla. Ath0
fra openBSD egen side.
Min Ifconfig ath0 ser sådan her ud, men jeg kan ikke connecte til det, ej
heller finde det via en netstumbler.
-bash-3.00# ifconfig ath0
ath0: flags=8863<UP,BROADCAST,NOTRAILERS,RUNNING,SIMPLEX,MULTICAST> mtu 1500
address: 00:02:6f:21:ed:28
ieee80211: nwid my_net chan 11 bssid 00:02:6f:21:ed:28
media: IEEE802.11 autoselect hostap (autoselect mode 11a hostap)
status: active
inet6 fe80::202:6fff:fe21:ed28%ath0 prefixlen 64 scopeid 0x4
inet 192.168.1.1 netmask 0xffffff00 broadcast 255.255.255.0
dmsg:
avail mem = 115593216 (112884K)
using 1658 buffers containing 6791168 bytes (6632K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 20/40/21, BIOS32 rev. 0 @ 0xf7840
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc8000/0x9000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Cyrix GXm PCI" rev 0x00
sis0 at pci0 dev 6 function 0 "NS DP83815 10/100" rev 0x00: DP83816A, irq
10, address 00:00:24:c3:60:64
nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1
sis1 at pci0 dev 7 function 0 "NS DP83815 10/100" rev 0x00: DP83816A, irq
10, address 00:00:24:c3:60:65
nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1
sis2 at pci0 dev 8 function 0 "NS DP83815 10/100" rev 0x00: DP83816A, irq
10, address 00:00:24:c3:60:66
nsphyter2 at sis2 phy 0: DP83815 10/100 PHY, rev. 1
hifn0 at pci0 dev 10 function 0 "Hifn 7955/7954" rev 0x00: LZS 3DES ARC4 MD5
SHA1 RNG AES PK, 32KB dram, irq 11
ath0 at pci0 dev 14 function 0 "Atheros AR5212" rev 0x01: irq 5
ath0: mac 80.9 phy 4.3 radio 3.6, 802.11a/b/g, FCC1A, address
00:02:6f:21:ed:28
gpio at ath0 not configured
gscpcib0 at pci0 dev 18 function 0 "NS SC1100 ISA" rev 0x00
gpio0 at gscpcib0: 64 pins
"NS SC1100 SMI/ACPI" rev 0x00 at pci0 dev 18 function 1 not configured
pciide0 at pci0 dev 18 function 2 "NS SCx200 IDE" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFB-128>
wd0: 1-sector PIO, LBA, 122MB, 250880 sectors
wd1 at pciide0 channel 0 drive 1: <HITACHI_DK23EA-30>
wd1: 16-sector PIO, LBA, 28615MB, 58605120 sectors
wd0(pciide0:0:0): using PIO mode 4
wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
geodesc0 at pci0 dev 18 function 5 "NS SC1100 X-Bus" rev 0x00: iid 6
revision 3 wdstatus 0
ohci0 at pci0 dev 19 function 0 "Compaq USB OpenHost" rev 0x08: irq 9,
version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: Compaq OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
isa0 at gscpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0 (mux 1 ignored for console): console keyboard
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
nsclpcsio0 at isa0 port 0x2e/2: NSC PC87366 rev 9: GPIO VLM TMS
gpio1 at nsclpcsio0: 29 pins
gscsio0 at isa0 port 0x15c/2: SC1100 SIO rev 1:
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
biomask f3c5 netmask ffe5 ttymask ffe7
pctr: no performance counters in CPU
dkcsum: wd0 matched BIOS disk 80
dkcsum: wd1 matched BIOS disk 81
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
arp info overwritten for 194.255.112.35 by 00:10:e0:06:0f:12 on sis1
arp info overwritten for 194.255.112.35 by 00:10:e0:06:0f:12 on sis1
arp info overwritten for 194.255.112.35 by 00:10:e0:06:0f:12 on sis1
syncing disks... done
OpenBSD 3.7 (GENERIC) #50: Sun Mar 20 00:01:57 MST 2005
deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Geode(TM) Integrated Processor by National Semi ("Geode by NSC"
586-class) 267 MHz
cpu0: FPU,TSC,MSR,CX8,CMOV,MMX
cpu0: TSC disabled
real mem = 133799936 (130664K)
avail mem = 115593216 (112884K)
using 1658 buffers containing 6791168 bytes (6632K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 20/40/21, BIOS32 rev. 0 @ 0xf7840
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc8000/0x9000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Cyrix GXm PCI" rev 0x00
sis0 at pci0 dev 6 function 0 "NS DP83815 10/100" rev 0x00: DP83816A, irq
10, address 00:00:24:c3:60:64
nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1
sis1 at pci0 dev 7 function 0 "NS DP83815 10/100" rev 0x00: DP83816A, irq
10, address 00:00:24:c3:60:65
nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1
sis2 at pci0 dev 8 function 0 "NS DP83815 10/100" rev 0x00: DP83816A, irq
10, address 00:00:24:c3:60:66
nsphyter2 at sis2 phy 0: DP83815 10/100 PHY, rev. 1
hifn0 at pci0 dev 10 function 0 "Hifn 7955/7954" rev 0x00: LZS 3DES ARC4 MD5
SHA1 RNG AES PK, 32KB dram, irq 11
ath0 at pci0 dev 14 function 0 "Atheros AR5212" rev 0x01: irq 5
ath0: mac 80.9 phy 4.3 radio 3.6, 802.11a/b/g, FCC1A, address
00:02:6f:21:ed:28
gpio at ath0 not configured
gscpcib0 at pci0 dev 18 function 0 "NS SC1100 ISA" rev 0x00
gpio0 at gscpcib0: 64 pins
"NS SC1100 SMI/ACPI" rev 0x00 at pci0 dev 18 function 1 not configured
pciide0 at pci0 dev 18 function 2 "NS SCx200 IDE" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFB-128>
wd0: 1-sector PIO, LBA, 122MB, 250880 sectors
wd1 at pciide0 channel 0 drive 1: <HITACHI_DK23EA-30>
wd1: 16-sector PIO, LBA, 28615MB, 58605120 sectors
wd0(pciide0:0:0): using PIO mode 4
wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
geodesc0 at pci0 dev 18 function 5 "NS SC1100 X-Bus" rev 0x00: iid 6
revision 3 wdstatus 0
ohci0 at pci0 dev 19 function 0 "Compaq USB OpenHost" rev 0x08: irq 9,
version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: Compaq OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
isa0 at gscpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0 (mux 1 ignored for console): console keyboard
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
nsclpcsio0 at isa0 port 0x2e/2: NSC PC87366 rev 9: GPIO VLM TMS
gpio1 at nsclpcsio0: 29 pins
gscsio0 at isa0 port 0x15c/2: SC1100 SIO rev 1:
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
biomask f3c5 netmask ffe5 ttymask ffe7
pctr: no performance counters in CPU
dkcsum: wd0 matched BIOS disk 80
dkcsum: wd1 matched BIOS disk 81
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
arp info overwritten for 194.255.112.35 by 00:10:e0:06:0f:12 on sis1
arpresolve: can't allocate llinfo
syncing disks... done
OpenBSD 3.7 (GENERIC) #50: Sun Mar 20 00:01:57 MST 2005
deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Geode(TM) Integrated Processor by National Semi ("Geode by NSC"
586-class) 267 MHz
cpu0: FPU,TSC,MSR,CX8,CMOV,MMX
cpu0: TSC disabled
real mem = 133799936 (130664K)
avail mem = 115593216 (112884K)
using 1658 buffers containing 6791168 bytes (6632K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 20/40/21, BIOS32 rev. 0 @ 0xf7840
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc8000/0x9000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Cyrix GXm PCI" rev 0x00
sis0 at pci0 dev 6 function 0 "NS DP83815 10/100" rev 0x00: DP83816A, irq
10, address 00:00:24:c3:60:64
nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1
sis1 at pci0 dev 7 function 0 "NS DP83815 10/100" rev 0x00: DP83816A, irq
10, address 00:00:24:c3:60:65
nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1
sis2 at pci0 dev 8 function 0 "NS DP83815 10/100" rev 0x00: DP83816A, irq
10, address 00:00:24:c3:60:66
nsphyter2 at sis2 phy 0: DP83815 10/100 PHY, rev. 1
hifn0 at pci0 dev 10 function 0 "Hifn 7955/7954" rev 0x00: LZS 3DES ARC4 MD5
SHA1 RNG AES PK, 32KB dram, irq 11
ath0 at pci0 dev 14 function 0 "Atheros AR5212" rev 0x01: irq 5
ath0: mac 80.9 phy 4.3 radio 3.6, 802.11a/b/g, FCC1A, address
00:02:6f:21:ed:28
gpio at ath0 not configured
gscpcib0 at pci0 dev 18 function 0 "NS SC1100 ISA" rev 0x00
gpio0 at gscpcib0: 64 pins
"NS SC1100 SMI/ACPI" rev 0x00 at pci0 dev 18 function 1 not configured
pciide0 at pci0 dev 18 function 2 "NS SCx200 IDE" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFB-128>
wd0: 1-sector PIO, LBA, 122MB, 250880 sectors
wd1 at pciide0 channel 0 drive 1: <HITACHI_DK23EA-30>
wd1: 16-sector PIO, LBA, 28615MB, 58605120 sectors
wd0(pciide0:0:0): using PIO mode 4
wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
geodesc0 at pci0 dev 18 function 5 "NS SC1100 X-Bus" rev 0x00: iid 6
revision 3 wdstatus 0
ohci0 at pci0 dev 19 function 0 "Compaq USB OpenHost" rev 0x08: irq 9,
version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: Compaq OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
isa0 at gscpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0 (mux 1 ignored for console): console keyboard
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
nsclpcsio0 at isa0 port 0x2e/2: NSC PC87366 rev 9: GPIO VLM TMS
gpio1 at nsclpcsio0: 29 pins
gscsio0 at isa0 port 0x15c/2: SC1100 SIO rev 1:
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
biomask f3c5 netmask ffe5 ttymask ffe7
pctr: no performance counters in CPU
dkcsum: wd0 matched BIOS disk 80
dkcsum: wd1 matched BIOS disk 81
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
arp info overwritten for 194.255.112.35 by 00:10:e0:06:0f:12 on sis1
Hvorfor kan jeg ikke finde det?
- Jakob -
> -----Oprindelig meddelelse-----
> Fra: owner-bsd-dk@hobbes.bsd-dk.dk [mailto:owner-bsd-dk@hobbes.bsd-dk.dk]
> På vegne af Henrik Kramshøj
> Sendt: 23. august 2005 09:15
> Til: bsd-dk@bsd-dk.dk
> Emne: Re: Accesspoit på en OpenBSD
>
>
> On 23/08/2005, at 0.53, Jakob Kjøller wrote:
>
> > Jeg sidder og prøver at findet en god HowTo om at lave et
> > accesspoint på en ath0 driver.
> >
> >
> >
> > Er der nogle som er stødt på en, eller evt. kender en bog med en
> > god forklaring?
> Jeg har ikke en god forklaring, men prøv evt at slå ned til 802.11b
>
> Ja, jeg ved godt det ikke er det man ønsker
>
> Jeg har et par Atheros kort og pt kan jeg kun få forbindelse hvis jeg
> sætter
> dem til 802.11b - og jeg skal også lige sætte country code i driveren
> når jeg kompilerer kernen.
>
> Så prøv
> 1) kig i dmesg - finder den kortet og er det iorden?
> 2) prøv samme setup med 802.11b
>
> Jeg ville nok følge current og læse hvad ændringer der kommer
> på driveren til ath - primært ar5xxx.h og .c tror jeg det er
> (sidder ude i byen)
>
> Mvh
>
> Henrik
> PS det skal måske bemærkes at de systemer jeg tester med er
> soekrisser med G520 tror jeg det hedder og en thinkpad med G650
> - jeg kan ikke huske hvad versioner af kortene
>
> --
> Henrik Lund Kramshøj, cand.scient, CISSP
> e-mail: hlk@security6.net, tlf: 2026 6000
> www.security6.net - IPv6, sikkerhed, netværk
> Follower of the Great Way of Unix
This archive was generated by hypermail 2b30 : Wed 15 Nov 2006 - 18:24:52 CET